1. Unplug MIDI and USB devices from RK-005
2. Keep this browser window open and active
GO
v1.9 FIRMWARE UPDATE
RK-005 firmware update is available, would you like to apply it?
YES
NO
USB PID/VID Inquiry
A list of recognised USB MIDI Device IDs. Use the VID/PID codes to enable individual filtering.
Querying...
CLOSE
x
DIN5 OUT PROPERTIES
Select operation mode for the DIN5 MIDI Out plug
COMMIT CHANGES
x
STEREO JACK PROPERTIES
RING
TIP
JACK RING MODE:
JACK RING HAS NO OUTPUT
CLOCK/TEMPO SIGNAL
You can select how many pulses the RK-005 will send out per sixteenth note.
Default rate matches PO/Volca speed. Use this setting to increase/decreate tempo relation between MIDI and analog clock.
GATE SIGNAL
In this mode the jack ring signal will output 3.3v if a MIDI note is pressed.
JACK TIP MODE:
JACK TIP HAS NO OUTPUT
CLOCK/TEMPO SIGNAL
You can select how many pulses the RK-005 will send out per sixteenth note.
Default rate matches PO/Volca speed. Use this setting to increase/decreate tempo relation between MIDI and analog clock.
GATE SIGNAL
In this mode the jack tip signal will output 3.3v if a MIDI note is pressed.
CV SIGNAL
In this mode the jack tip signal will output an analog signal up to 3.3v. Voltage level can be mapped to the parameters below. Use this in combination with the Jack-ring in gate mode to trigger analog gear.
This mode plays like most monophonic synths: The latest played key defines tone height
The lowest key of all keys played defines tone height
The highest key of all keys played defines tone height
Velocity of any key pressed will set CV value
Defined #CC number will set CV value
Pitchbend will define CV value; High resolution, might be useful for microtuning)
Aftertouch of any key pressed will set CV value
MIDI /CV Basekey
CV Controller #
MIDI /CV Response channel
PULSE RATE
PRESETS:
off
Volca / PO
Uno Synth
MIDI
COMMIT CHANGES
x
LED PROPERTIES
Set LED color and intensity offsets:
RED
GREEN
BLUE
ACTIVITY
COMMIT CHANGES
x
RK-005 FILTER SETTINGS
Here you can set filters to mute various MIDI messages WARNING: This is for advanced troubleshooting only!
FILTER 1
FILTER 2
FILTER 3
FILTER 4
Applies to:
FILTER 1 DETAILS
Filter applies on:
Device USB VID/PID (even advancederer!) VID PID
Filter applies on MIDI data :
Filtered MIDI Channel(s):
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Applies to:
FILTER 2 DETAILS
Filter applies on:
Device USB VID/PID (even advancederer!) VID PID
Filter applies on MIDI data :
Filtered MIDI Channel(s):
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Applies to:
FILTER 3 DETAILS
Filter applies on:
Device USB VID/PID (even advancederer!) VID PID
Filter applies on MIDI data :
Filtered MIDI Channel(s):
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Applies to:
FILTER 4 DETAILS
Filter applies on:
Device USB VID/PID (even advancederer!) VID PID
Filter applies on MIDI data :
Filtered MIDI Channel(s):
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
COMMIT CHANGES
x
FACTORY RESET
Are you sure you want to initialize all port settings and filters?
